Prediction of Shear Strength in SCS Panels with One-End Welded BP Shear Connector Using Numerical Modeling and Gene Expression Programming (GEP)

Document Type : Research Article

Authors

1 Civil Engineering Department, University of Sistan and Baluchestan, Zahedan, Iran

2 Civil Engineering and Architectural Department, Faculty of Engineering, University of Torbat Heydarieh, Torbat Heydarieh, Iran

Abstract

Steel-concrete-steel (SCS) sandwich structures, comprising steel faceplates and a concrete core, are valued for their strength and durability. Among various shear connectors, one-end welded box-profile (BP) connectors have shown strong potential in resisting interfacial shear forces. However, no precise formula exists to estimate their shear strength, especially considering the overlap ratio. This study addresses this gap by developing a predictive model for the shear strength of these connectors. Using the Taguchi experimental design, 18 numerical models were created, varying connector width, thickness, concrete core strength, and overlap ratio. Finite element simulations, validated against experimental push-out tests, analyzed load-slip behavior and failure modes. A Gene Expression Programming (GEP) algorithm was applied to derive an equation linking shear strength to geometric and material properties.The resulting equation demonstrated high accuracy, with a correlation coefficient (R) of 0.919 and lower error metrics compared to existing methods. By incorporating overlap ratio effects, this model provides engineers with a more precise tool for designing safer and more efficient SCS systems. The findings enhance the understanding of BP connector mechanics and offer a cost-effective approach for optimizing SCS structures in various structural applications.

Keywords

Main Subjects

References

[1] R.S.N. Shariati M, Shariati A, Kueh ABH, Comparative performance of channel and angle shear connectors in high-strength concrete composites: An experimental study, Constr Build Mater, (92) (2016) 120:382.
[2] N. Malek, Steel-concrete sandwich members without shear reinforcement, Transactions of Japan Concrete Institute (23) (1993) 27-34.
[3] Z. Huang, J.R. Liew, Nonlinear finite element modelling and parametric study of curved steel–concrete–steel double skin composite panels infilled with ultra-lightweight cement composite, Construction and Building Materials, 95 (2015) 922-938.
[4] Y. Lin, J. Yan, Y. Wang, F. Fan, C. Zou, Shear failure mechanisms of SCS sandwich beams considering bond-slip between steel plates and concrete, Engineering Structures, 181 (2019) 458-475.
[5] Y. Lin, J. Yan, Z. Cao, X. Zeng, F. Fan, C. Zou, Ultimate strength behaviour of S-UHPC-S and SCS sandwich beams under shear loads, Journal of Constructional Steel Research, 149 (2018) 195-206.
[6] Z. Wang, J. Yan, Y. Lin, F. Fan, Y. Yang, Mechanical properties of steel-UHPC-steel slabs under concentrated loads considering composite action, Engineering Structures, 222 (2020) 111095.
[7] M. Xie, N. Foundoukos, J. Chapman, Experimental and numerical investigation on the shear behaviour of friction-welded bar–plate connections embedded in concrete, Journal of Constructional Steel Research, 61(5) (2005) 625-649.
[8] N. Anandavalli, J. Rajasankar, A. Prakash, B. Sivaprasad, Static response of steel-concrete-steel sandwich beam with bi-directionally inclined connectors, American Journal of Civil Engineering and Architecture, 1(1) (2013) 15-20.
[9] Y.-T. Guo, M.-X. Tao, X. Nie, S.-Y. Qiu, L. Tang, J.-S. Fan, Experimental and theoretical studies on the shear resistance of steel–concrete–steel composite structures with bidirectional steel webs, Journal of Structural Engineering, 144(10) (2018) 04018172.
[10] J.-B. Yan, Y.-Y. Yan, T. Wang, Z.-X. Li, Seismic behaviours of SCS sandwich shear walls using J-hook connectors, Thin-Walled Structures, 144 (2019) 106308.
[11] W. Zhang, Z. Huang, Z. Fu, X. Qian, Y. Zhou, L. Sui, Shear resistance behavior of partially composite Steel-Concrete-Steel sandwich beams considering bond-slip effect, Engineering Structures, 210 (2020) 110394.
[12] J.-B. Yan, H. Hu, T. Wang, Flexural behaviours of steel-UHPC-steel sandwich beams with J-hook connectors, Journal of Constructional Steel Research, 169 (2020) 106014.
[13] H. Roshani, M. Yousefi, N. Gharaei-Moghaddam, S.H. Khatibi, Flexural performance of steel-concrete-steel sandwich beams with lightweight fiber-reinforced concrete and corrugated-strip connectors: Experimental tests and numerical modeling, Case Studies in Construction Materials, 18 (2023) e02138.
[14] M. Yousefi, S.H. Khatibi, Experimental and numerical study of the flexural behavior of steel–concrete-steel sandwich beams with corrugated-strip shear connectors, Engineering Structures, 242 (2021) 112559.
[15] M. Yousefi, M. Ghalehnovi, Push-out test on the one-end-welded corrugated-strip connectors in steel-concrete-steel sandwich structure, Steel Compos. Struct, 24(1) (2017) 23-35.
[16] M. Yousefi, M. Ghalehnovi, Finite element model for interlayer behavior of double skin steel-concrete-steel sandwich structure with corrugated-strip shear connectors, Steel Compos. Struct, 27(1) (2018) 123-133.
[17] S.H. Khatibi, H.G. Arab, M. Miri, Interlayer behavior investigation of box profile shear connectors in steel-concrete-steel sandwich structures, in:  Structures, Elsevier, 2022, pp. 1031-1042.
[18] S.H. Khatibi, H.G. Arab, M. Miri, The behavior of steel-concrete-steel sandwich composite beams with box-profile shear connectors: Experimental and numerical, in:  Structures, Elsevier, 2023, pp. 644-656.
[19] M. Daliri, H.G. Arab, M. Miri, S.H. Khatibi, Overlap effects of one-end welded box-profile shear connectors on interlayer shear behavior, in:  Structures, Elsevier, 2025, pp. 107982.
[20] K.M.A. Sohel, J.R. Liew, C.G. Koh, Numerical modelling of lightweight Steel‐Concrete‐Steel sandwich composite beams subjected to impact, Thin-Walled Structures, 94 (2015) 135-146.
[21] X.-L. Gao, J.-Y. Wang, C. Bian, R.-C. Xiao, B. Ma, Experimental investigation on the behaviour of UHPC-steel composite slabs under hogging moment, Steel and Composite Structures, An International Journal, 42(6) (2022) 765-777.
[22] J.-B. Yan, J.R. Liew, M.-H. Zhang, K. Sohel, Experimental and analytical study on ultimate strength behavior of steel–concrete–steel sandwich composite beam structures, Materials and Structures, 48 (2015) 1523-1544.
[23] Z. Huang, J.R. Liew, Structural behaviour of steel–concrete–steel sandwich composite wall subjected to compression and end moment, Thin-Walled Structures, 98 (2016) 592-606.
[24] J.-B. Yan, Finite element analysis on steel–concrete–steel sandwich beams, Materials and Structures, 48(6) (2015) 1645-1667.
[25] C. Xue, Z. Fan, F. Wu, L. Liu, L. He, X. Cui, Research on the shear behaviour of composite shear connectors, Buildings, 12(10) (2022) 1726.
[26] M. Yousefi, M. Golmohammadi, S.H. Khatibi, M. Yaghoobi, Prediction of the punching load strength of SCS slabs with stud-bolt shear connectors using numerical modeling and GEP algorithm, Journal of Rehabilitation in Civil Engineering, 11(3) (2023) 68-87.
[27] A.S.U.s. Manual, Abaqus 6.11, http://130.149, 89(2080) (2012) v6.
[28] S. ZANJIRCHI, F. AZIZI, M. AMANI, DEVELOPING A MODEL FOR FORECASTING THE SUCCESS OF CONSTRUCTION PROJECTS INTEGRATION TAGUCHI (DOE) AND TAXONOMY,  (2017).
[29] S.K. Khrais, Y. Lin, Wear mechanisms and tool performance of TiAlN PVD coated inserts during machining of AISI 4140 steel, Wear, 262(1-2) (2007) 64-69.
[30] F.S. Hoseinian, B. Rezai, E. Kowsari, Kinetic constant modeling of Zn (II) ion removal from synthetic wastewater by gene expression programming, Amirkabir Journal of Civil Engineering, 53(1) (2021) 261-272.
[31] D. Muñoz, Thesis Discovering unknown equations that describe large data sets using genetic programming techniques, Masters Thesis, Linköping Institute of Technology, 2005.
[32] D. Jahed Armaghani, R.S. Faradonbeh, E. Momeni, A. Fahimifar, M. Tahir, Performance prediction of tunnel boring machine through developing a gene expression programming equation, Engineering with Computers, 34(1) (2018) 129-141.
[33] C. Européen, Eurocode 2: Design of concrete structures—Part 1-1: General rules and rules for buildings, London: British Standard Institution,  (2004) 37.
[34] A. Specification, Specification for structural steel buildings, ANSI/AISC, 36010 (2005).
[35] L. Aashto, Bridge design specifications,  (1998).
AUT Journal of Civil Engineering
Volume 9, Issue 3
November 2025
Pages 185-204

Files

Share

How to cite

Statistics